Fluke network inspector 4.17/10/2023 Output Voltage Level in Continuity Mode: 8 Vdc with fresh battery.Output Power in Tone Mode: 8 dbm into 600 ohms.Over Voltage Protection: 60 Vdc in Toner/Polarity Mode.Alternating Frequency: 1000/1500 Hz nominal.User interface: Slide switch selects Continuity or Tone Mode Push button switch selects SOLID, ALT or OFF Tone mode LED Continuity/Polarity LED.Whether it’s because your hearing isn’t what it used to be, you work around challenging cable bundles, or you’re just trying to make the job easier, I can highly recommend this kit for cable and wire identification. For the communications installs I do, it functions beautifully. The big draw for the Fluke Networks Pro3000F60 Tone and Probe Kit is its ability to filter. If you don’t feel like you need the filtering, you can get the Fluke Networks Pro3000 Kit for $72.17. Tone and probe sets start under $50 and this price isn’t bad for a high-end model that filters out the extra noise. You can pick up the Fluke Networks Pro3000F60 Tone and Probe Kit online for $109.74. I’m really glad to see that the Pro3000F60 definitely holds up to the Fluke reputation I’m used to in both function and durability. I’ve used my 727 Process Meter for years and it still keeps coming back to work. The probe’s ability to trace through drywall was a HUGE help and kept us from having to switch to a separate tracing instrument. On another office building project, we had the unenviable task of tracing some pretty old existing runs and create a network infrastructure map. Some of these are long enough to be a bit sketchy with our other tone and probe systems, but the Fluke Networks Pro3000F60 didn’t have an issue with them at all. We started by pulling a ton of Cat 5 runs in through our shop for a demo unit we’re building. I mainly work with Cat 5, so the alligator clamps are what I turn to most frequently. The toner includes a pair of alligator clamps and an RJ-11 connector for terminated phone jacks. If you’re not sure what mode you’re in, take a peek at the LED-it matches the mode (constant, flashing, off).įlip the switch to ‘”cont” to check continuity. Start with the switch in the “tone” position and press the button on the left to cycle between constant, alternative, and power off. You can choose between constant and alternating tones. It’s strong enough to send a tone up to 10 miles down the line on many cables. Looking at the Fluke Networks Pro3000 Toner, there are 5 different tones you can send to dial in the exact pair you’re identifying. When you don’t want or need to use headphones, the built-in speaker is plenty loud enough for general identification. Just plug in a set of headphones or earbuds and let your ears hone in better. The Fluke Networks Pro3000F60 (and Pro3000 analog) have a 3.5 mm jack on the side. Ambient noise from work going on around you doesn’t help. When you’re working around cable or wire bundles, it can be challenging to figure out exactly which wire the tone is on. Pro Tip: The LED doesn’t light up and the volume decreased when your battery is close to dead.Įven though there’s a filter, you still need to use this on an inactive line. If you don’t want to use, press the button and it turns red to let you know it’s off. When you turn the probe on, a green light lets you know that the filter is also on. Here in the US, we’re on a 60Hz system, so our Pro3000F is set to filter out that frequency. The Fluke Networks Pro3000F60 (or Pro3000F50 in 50 Hz areas) filters out the extra noise to make it easier to identify or trace your line amongst others. While the toner sends a clearly different signal from all that, the additional noise can make it difficult to identify which wire actually has the tone in it. With a traditional tone and probe set, any live wires send a signal that the probe can pick up.
0 Comments
Leave a Reply. |